Your First Choice for Pumps and Pump Systems
Call Icon Call (305)-754-0677 M-F 8am - 4pm EST | Contact | FAQ

Rule Pumps Rule-A-Matic Plus 20 Amp 12 VDC Float Switch # 40 A(D)

Item#: RUL-CTL-40A
Product Not Available Not Available
Rule Pumps Rule-A-Matic Plus  20  Amp 12 -24-32 VDC Float Switch # 40A (D)<br>
Reg. $68.56
Sale: $44.98
Out of Stock

Rule model 40 Rule-A-Matic Plus Switch without fuse holder, is compact, sleek, and rugged. It has a strong, fully integrated, impact resistant cover, which protects against debris and jamming. Wires exit out on the top to keep them out of the water. Dual level anti-clog water slots.. Manual testing feature allows for operations check.Use with pumps up to 20 amps. Environmentally friendly mercury-free design. NOT to be used with 110V applications

Specifications

Application: Bilge pump flow switch Operation: Automatically activates bilge pumps. Turns pump on when water level reaches 2"; turns pump off when water level reaches 3/4" Rating: For use with 12, 24 and 32 volt DC bilge pumps 20 Amps or less. NOT TO BE USED WITH 110V APPLICATIONS Maximum Amps: 20 Amps Fuse Holder:None Cover:Fully integrated cover for jamming, debris and impact protection. Testing Feature:Manual Wiring:Abrasion resistant wires exit out the top. Protection: Ignition protected Dimensions: 2-3/4"H x 4-7/8"L x 2-1/2"W.

Questions & Answers

These float switches are designed for use with fresh water and salt water ONLY. Use with any other hazardous, caustic, or corrosive material could result in damage to the pump and the surrounding environment, possible exposure to hazardous substances and injury.
Disconnect power from the system before working on the unit to avoid personal injury, damage to the surrounding environment and/or damage to the unit.
Switch must be mounted equal to or above the pump base for positive shut-off.
Keep all wire connections above the highest water level. Wires must be joined with butt connectors and a marine grade sealant to prevent wire corrosion.
Always install proper fuse size to prevent damage to product should a short occur. Failure to install proper fuse could increase risk of pump malfunction potentially resulting in personal injury and/or fire hazard
It is recommended you mount the float switch on a level platform although the float switch can be mounted up to a 15 degree angle. Note: Model 40 Float Switch if mounting fore and aft centerline of vessel, point wires to exit towards the stern.
Connect the Brown (Positive) wire from the pump to one Gray wire from Float Switch. Connect the other Gray wire from the Float Switch directly to Positive power supply (Fuse Protected). The Black (Negative) wire from the Bilge pump connects to the Negative battery terminal or Negative buss bar. Wire the pump directly to the power supply, this will ensure the pump has power if the power system on boat has been isolated.
One Gray wire from the float switch connects to the solid Brown (Positive) wire from Non-Automatic Bilge Pump. The Third wire needs to be connected and run directly to the two position Panel Switch. The other Gray wire should be connected directly to the Positive power supply (Fuse Protected). Connect the Black (Negative) wire to the Negative battery terminal or buss bar. Wire the Bilge pump directly to the power supply, this will ensure the pump has power if the power system on boat has been isolated.
One Gray wire from the Float Switch connects to the solid Brown (Positive) wire from Non-Automatic Bilge Pump. The third wire should to be connected directly to Manual side of Panel Switch. The other Gray wire from the Float Switch connects directly to the Automatic side of Panel Switch. Connect the Black (Negative) wire to Negative battery terminal or buss bar. Wire the Bilge pump directly to power supply, this will ensure that pump has power if the power system on boat has been isolated.

(?) Ask a question about Rule Pumps Rule-A-Matic Plus 20 Amp 12 -24-32 VDC Float Switch # 40A (D)
Back to Top